Tefal Plancha Booster test: an affordable option for grilled meat lovers

Tefal Plancha Booster test: an affordable option for grilled meat lovers


Convenience of use

The Plancha Booster can be used at the table, but it takes up some space with its impressive power supply for connection in an extension of an already relatively long board. It is also necessary to provide an extension cable, as its cable is a little short (1.20 m). As with the Colormania XL, the plate rests on a plastic base, but Tefal offers a much more modest black color.

Tefal Plancha Booster

Tefal Plancha Vooster is long, very long.

Tefal Plancha Booster

The control panel is also located in the electrical block.

The plate in question offers a cooking surface of 50 x 26 cm withfitness area“On the right half. This will allow you to benefit from excess energy thanks to a special resistance for cooking thick meat. It is activated and deactivated with a simple button, while a graduated dimmer from 1 to 6 allows you to set the power for the entire plate.

Despite the use of non-stick coating it is “fitness zone” It allowed us to get a nice color on the steak. However, this is not comparable to what can be obtained on a stainless steel plate such as Plancha Pro from Lagrange, and yet we would rather find truly independent cooking zones with a dimmer for each of them, as is the case with Riviera & Bar. QPL665. Some models, such as the Plancha Saveur double from Krampouz, even offer thermostats that allow you to select the temperature for each zone.

Tefal Plancha Booster

Plancha Booster can also cook vegetables.

Plancha Booster does not contain a real warm-up indicator. The light above the dimmer will illuminate when it is connected, and the Booster controller will contain another that indicates that it is on, but none shows the status of the resistor. To let you know when the plate is hot, Tefal still has its famous Thermospot indicator: a pellet whose patterns disappear from a certain temperature.

Thanks to the non-stick layer, the food does not stick to the plate during cooking. It is therefore not necessary to add fat, but in return you will need to make sure that you only use wooden or plastic tools to store it. However, if fat is used, or if the food only excretes water or juice, small holes are available to allow liquids to drain from the plate. At the bottom is a large drip tray and the plate is tilted slightly to facilitate drainage.

Tefal Plancha Booster

Collection tank.

However, it should be noted that Tefal does not contain a rim against splash water. This certainly allows all guests easy access to the plate if the device is used in the middle of the table, but it is therefore better to add protection. Although it is better to opt for heat-resistant protection, we have not noticed any overheating under the device. However, the tower can heat up, but not as much as Lono Grill and Plancha.

When the Plancha Booster is not in use, it can be stored relatively easily by unplugging the power cord. Note that it is not possible to leave it outside without a shelter, as it is not weatherproof, unlike, for example, Plancha Pro from Lagrange. Tefal does not even recommend using it outdoors.

Editors' rating: 3 of 5

Easy maintenance

Plancha Booster must be cleaned after each use. The operation is performed only after the appliance has cooled down completely, so that you do not get burned, of course, but also because the non-stick layers do not withstand thermal shocks. It is therefore better to avoid polishing to loosen the residue, as opposed to what can be done on stainless steel sheet.

Tefal Plancha Booster

It is also not always recommended to use an abrasive sponge to maintain this coating, but it also allows it not to be scrubbed too much to remove residue. An ordinary sponge with water and dishwashing detergent is therefore sufficient to clean the plate by hand. It is also possible to immerse it completely under water in the sink, but since it is not removable, the hob must be taken with the base and handling the assembly can be difficult. You can also put everything in the dishwasher, but the dimensions are binding again.

Before cleaning, it is of course necessary to unplug the appliance and remove its drive, and you must also remember to remove the juice collector before moving it. It pops out like a drawer. It can then be cleaned by hand or in a dishwasher.

Editors' rating: 3 of 5

Cooking

The Plancha Booster is equipped with a 2200 W resistor and a power variator graded from 1 to 6, with intermediate notches for even finer power settings.

The appliance must be preheated before use. It is therefore advisable to set it to maximum power and wait. The Plancha Booster is not particularly fast, but it is not nearly as slow as the Plancha Pro from Lagrange and the Plancha Saveur double from Krampouz with their thick stainless steel plate. After 3 min 35 s, the plate reached the reference temperature defined for our tests, namely 230 ° C. However, it is better to let the Plancha Booster preheat longer, as it has finally risen to 310 ° C. The temperature then drops and remains at more reasonable levels.

Maximum temperature recorded on the surface of the Tefal Plancha Booster.

Maximum temperature recorded on the surface of the Tefal Plancha Booster.

We could also leave it at power 6 to continue the measurement, as it is ultimately the one that allows us to approach a maximum of 230 ° C after preheating. However, it must be acknowledged that approach is a very big word for Planch Booster. Like all planks, the heating and pause phases alternate to stabilize the temperature, but these are too long and the plate too thin to keep warm. This results in fluctuations of plus or minus 100 ° C depending on the measuring point selected on the plate, which poses a risk of slowing down the cooking.

Tefal Plancha Booster surface temperature changes.

Tefal Plancha Booster surface temperature changes.

This is also a relatively common problem with Tefalu: all the plancha brands we have tested so far are struggling with temperature stabilization. Maybe it would be good to be a little inspired by WMF, also in the Seb group and by the creation of Lono Grill and Plancha, which will not let them drop by more than 50 ° C.

In terms of homogeneity, it’s also not exactly famous. During the heating phases, we noticed an difference of up to 80 ° C on the cooking surface. And the main resistance is satisfied that it follows the edge of the board without going through the center. By activating the booster, homogeneity is improved in the right half, because the second resistor lights up in the middle of the zone, but then it will not be possible to cook too brittle food because the temperature is higher there.

The temperature becomes more even when the Plancha Booster stops heating, but as mentioned above, it can then drop by 100 ° C and slow down the cooking.

Temperature differences on the surface of the board, during and after heating.

Temperature differences on the surface of the board, during and after heating.



Source link

Leave a Comment

Your email address will not be published.